Serwis korzysta z plików cookies w celu świadczenia spersonalizowanych usług na najwyższym poziomie, w tym usług statystycznych oraz w celu dostosowania zawartości do indywidualnych preferencji użytkowników. Zapisywanie plików cookies można wyłączyć w ustawieniach przeglądarki. Więcej informacji
OK
Utwórz konto
[zamknij]     

BONDERITE L-FG F 31 - 1100kg (bezwonny, bezdymny, grafitowy smar na bazie wody / odourless, smokeless, water-based graphite lubricant)

Nr

IDH.1395617

BONDERITE L-FG F 31 - 1100kg (bezwonny, bezdymny, grafitowy smar na bazie wody / odourless, smokeless, water-based graphite lubricant)

BONDERITE L-FG F 31 - 1100kg (bezwonny, bezdymny, grafitowy smar na bazie wody / odourless, smokeless, water-based graphite lubricant) (IDH.1395617)

Product description:
BONDERITE L-FG F 31 ACHESON is the world’s most widely used forging die lubricant. BONDERITE L-FG F 31 ACHESON exhibits excellent stability with no separation or settling in the concentrate. This assures constant quality from top to bottom and results in consistent forging performance. BONDERITE L-FG F 31 ACHESON is an essentially odourless, smokeless, water-based graphited die lubricant. It is formulated to provide excellent lubricity and release when used on difficult press work and highly automated processes, including hot, warm, and precision forging. BONDERITE L-FG F 31 ACHESON contains a unique graphite particle size and configuration, along with a special stabiliser and binder system. These properties produce excellent lubricity and release, faster wetting, higher dilution ratios, and longer die life. Further information about the product: biuro@woronko-kleje.pl

Application Areas:
Due to its high stability this product can be used in hard water without the risk of precipitations. BONDERITE L-FG F 31 ACHESON is used as a lubricant for hot forging steel, precision forging, warm forging steel and hot forging powder metal.

Directions for use:
Prior to use it is necessary to read the Material Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed. Please also refer to the local safety instructions and contact Henkel for analytical support.

Dilution:
BONDERITE L-FG F 31 ACHESON is supplied as a concentrate and can normally be diluted with ordinary tapwater prior to use. However, if the tap water is extremely high in mineral content, check with your HENKEL representative for assistance. Add water to the concentrate, not the reverse. Stir the concentrate thoroughly, then add one part water slowly while stirring until the mixture is homogenous. The remaining water may be added rapidly while stirring until the desired dilution is reached.

Dilution Ratios:
The recommended dilution ratio depends on the difficulty of the job and the cooling required. For initial trials, a ratio of one part BONDERITE L-FG F 31 ACHESON to ten parts water by volume is proposed. Ratios of 1 : 20 and greater are commonduring production. Use a more concentrated mixture, 1 : 3 (product:diluent), to lubricate tooling hotter than 320°C.

Application:
For best results, diluted BONDERITE L-FG F 31 ACHESON should be applied by conventional spray techniques. Sprayapplication provides uniform coating thickness, complete die coverage, and lower friction values.

Storage:
  • 24 months from date of qualification under original seal.
  • Store BONDERITE L-FG F 31 ACHESON in a cool place, but do not allow it to freeze.
  • Product should not be used once frozen.
  • Always tightly reseal the container to prevent evaporation or contamination.

    Parameters:
  • Pigment/Lubricating : solid high purity micro-graphite
  • Carrier: water
  • Consistency : medium viscous liquid
  • Density, kg/m³ : 1,090
  • pH-value : ~11.5
  • Solids, % ~18

    Full technical information about the product is in the technical data sheet.
  • Asortyment