TEROSON WT S3000 BK AQUA - 1l (ochrona przed uderzeniami kamieni, czarny)
Nr
IDH.882415
Cena
129,87 PLN netto
Product description:
TEROSON WT S3000 AQUA is a coating compound based on an aqueous synthetic resin dispersion which can be sprayapplied with UBC-guns, filler or paint pistols. Drying times are dependent on the thickness of the coating applied, on ambient temperatures and on the relative humidity of the ambient air. Drying is considerably faster if good ventilation and relatively high temperatures are provided. The dry film adheres well to zinc-coated and electro-coated steel sheet metal and to painted surfaces. Because of its high abrasion resistance and its good flexibility TEROSON WT S3000 AQUA offers excellent protection to scratches, stonechips and other such marks. TEROSON WT S3000 AQUA is processable / overpaintable with waterborne paints. When fully air dried (at the earliest after 6 hours) the coating can be painted over with standard vehicle refinish paint systems (including solvent born paints). After complete drying the coating can be sanded. TEROSON WT S3000 AQUA is temporarily resistant against fuels and cold cleaners. TEROSON WT S3000 AQUA is suitable for restoring the original structure after a repair.
Applications areas:
TEROSON WT S3000 AQUA is used for repair/touch up jobs of the underbody, wheel houses, front and rear areas (aprons). It can be applied to visible parts of e.g. door sills as an overpaintable protection against road stone chip or as a protection against corrosion caused by salt and humidity. TEROSON WT S3000 AQUA is ideally suited to recreate the different surface textures produced at original manufacture, for the perfect visible repair. Its outstanding benefit are the multifarious possibilities of the dyeing the material. Scratchesor other small injuries of the paint remains nearly invisible. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pretreatment
The surfaces to be coated with TEROSON WT S3000 AQUA have to be clean, dry and free of rust, oil, grease, dust and other contamination. Areas not to be coated should be properly covered. Bare sheet steel must always be coated with wash primer prior to coating with TEROSON WT S3000 AQUA
Application
TEROSON WT S3000 AQUA is applied with the Henkel UBC-Gun from 1-l-cans. Recommended application pressureis 3 - 5 bar. Shake the can well before use. Fine surface structures can be obtained with the spray gun.
Caution
Do not spray onto joints, engine, gear box, prop shaft, transmissions, exhaust components, catalytic converter and the break system. A blocked gun may cause the can to burst. Follow the operating instructions for the gun.
Storage:Frost sensitive : yes Recommended storage temperature : 10 to 25 °C Shelf life : 12 months
Parameters: Colour : white, grey, black Odour : slight odour of ammonia Density : approx. 1.2 to 1.25 g/cm³ Consistency : liquid Solids : approx. 67 % Sag resitance : up to 1 mm wet
Full technical information can be found in technical data sheet
TEROSON WT S3000 AQUA is a coating compound based on an aqueous synthetic resin dispersion which can be sprayapplied with UBC-guns, filler or paint pistols. Drying times are dependent on the thickness of the coating applied, on ambient temperatures and on the relative humidity of the ambient air. Drying is considerably faster if good ventilation and relatively high temperatures are provided. The dry film adheres well to zinc-coated and electro-coated steel sheet metal and to painted surfaces. Because of its high abrasion resistance and its good flexibility TEROSON WT S3000 AQUA offers excellent protection to scratches, stonechips and other such marks. TEROSON WT S3000 AQUA is processable / overpaintable with waterborne paints. When fully air dried (at the earliest after 6 hours) the coating can be painted over with standard vehicle refinish paint systems (including solvent born paints). After complete drying the coating can be sanded. TEROSON WT S3000 AQUA is temporarily resistant against fuels and cold cleaners. TEROSON WT S3000 AQUA is suitable for restoring the original structure after a repair.
Applications areas:
TEROSON WT S3000 AQUA is used for repair/touch up jobs of the underbody, wheel houses, front and rear areas (aprons). It can be applied to visible parts of e.g. door sills as an overpaintable protection against road stone chip or as a protection against corrosion caused by salt and humidity. TEROSON WT S3000 AQUA is ideally suited to recreate the different surface textures produced at original manufacture, for the perfect visible repair. Its outstanding benefit are the multifarious possibilities of the dyeing the material. Scratchesor other small injuries of the paint remains nearly invisible. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pretreatment
The surfaces to be coated with TEROSON WT S3000 AQUA have to be clean, dry and free of rust, oil, grease, dust and other contamination. Areas not to be coated should be properly covered. Bare sheet steel must always be coated with wash primer prior to coating with TEROSON WT S3000 AQUA
Application
TEROSON WT S3000 AQUA is applied with the Henkel UBC-Gun from 1-l-cans. Recommended application pressureis 3 - 5 bar. Shake the can well before use. Fine surface structures can be obtained with the spray gun.
Caution
Do not spray onto joints, engine, gear box, prop shaft, transmissions, exhaust components, catalytic converter and the break system. A blocked gun may cause the can to burst. Follow the operating instructions for the gun.
Storage:
Parameters:
Full technical information can be found in technical data sheet