Serwis korzysta z plików cookies w celu świadczenia spersonalizowanych usług na najwyższym poziomie, w tym usług statystycznych oraz w celu dostosowania zawartości do indywidualnych preferencji użytkowników. Zapisywanie plików cookies można wyłączyć w ustawieniach przeglądarki. Więcej informacji
OK
Utwórz konto
[zamknij]     

TEROSON PU 9200 BK - 310ml (masa klejąco uszczelniająca, czarna, dawny Terostat 9200 PUR)

Nr

IDH.1896972

Cena

55,50 PLN netto

TEROSON PU 9200 BK - 310ml (masa klejąco uszczelniająca, czarna, dawny Terostat 9200 PUR)

TEROSON PU 9200 BK - 310ml (masa klejąco uszczelniająca, czarna, dawny Terostat 9200 PUR) (IDH.1896972)

Product description:
TEROSON PU 9200 is a one component adhesive/sealant based on polyurethane, which cures by reaction with moisture to a soft elasticproduct. The skin formation and curing times are dependent on humidity and temperature. The curing time also depends on joint depth. By increasing the temperature and moisture these times can be reduced. Low temperature as well as low moisture retards the process. Further information about the product: biuro@woronko-kleje.pl


TEROSON PU 9200 exhibits the following properties:
- good adhesion to painted surfaces, many metals and plastics without primer
- can be overpainted
- sag resistant
- high curing speed
- excellent elasticity

Application areas
TEROSON PU 9200 is used for elastic bonding and sealing in the automotive repair business. Temporary fixation of the joint with adhesive tapes or spacers is advised until the adhesive/sealant has completely cured. TEROSON PU 9200 offers the important advantage that both bonding and sealing functions can be achieved with one product. The material is not generally suitable for constructive bonding.

Directions for use:
Pretreatment
The surfaces to be bonded or sealed must be dry, free of oil, dust, grease and other contaminants. For pretreatment we recommend the approved cleaners of the TEROSON program (TEROSON VR 20), because other cleaners may lead to incompatibilities.

Application
TEROSON PU 9200 can be directly applied from cartridges employing standard air or hand operated guns. For air pressure application 2 to 5 bar are necessary. Low material temperature will lead to an increase of viscosity, resulting in a lower extrusion rate.This can be avoided by bringing the material up to room temperature prior to application. To avoid condensation it is necessary to bring the substrates up to room temperature. After application TEROSON PU 9200 can be smoothed with a spatula dipped in water or TEROSON VR 20.

Storage:
  • Frost sensitive : no
  • Recommended storage temperature : 10 to 25 °C
  • Shelf life : 9 months in original packaging

    Parameters:
  • Colour : black
  • Density : approx. 1.2 g/cm³
  • Odour : aromatic (no smell after curing)
  • Consistency : pasty
  • Sag resistance : very good
  • Curing mechanism : moisture curing
  • Skin formation time (23°C, 50% rh) : approx. 35 min(s).
  • Cure rate (23°C, 50% rh) : approx. 4 mm/ 24 hour(s)
  • Shore A hardness : approx. 45
  • Tensile strength : approx. 1.7 MPa
  • Elongation at break : approx. 350 %
  • Application temperature : 5 to 35 °C

    Further information about product can be found in technical data sheet
  • Asortyment