TEROSON PU 8597 HMLC - 310ml (jednoskładnikowy klej poliuretanowy, do szyb, szybki, dawny Terostat 8597 HMLC)
Nr
IDH.1467799
Product description:
The direct glazing adhesive is outstanding for the following properties:
- Very good sag resistance
- High cure rate
- High elastic and shear strength, even after aging
- Very low conductivity
- Good adhesion to the remaining material
- High shear modulus
- High UV resistance in connection with primer/activator
- Excellent adhesion to glass, glass with the ceramic coating, encapsulation and to painted surfaces, in connection withprimer/activator
Further information about the product: biuro@woronko-kleje.pl
Application Areas:
TEROSON PU 8597 HMLC is used for the bonding of front, rear and side screens to the body of motor-, utility-, special- and rail vehicles.
Directions for use:
Surface Preparation:
The substrates to be bonded must be dry and free from oil, dust, grease and other contaminations. Check new glass if it is correct and free of any damage. To obtain an optimal adhesion on the new screen we recommend 2 different surface preparation methods (solvent based, TEROSON VR 10 or waterborne, TEROSON VR 100):
1. Wipe off surface with a lint free cloth and TEROSON VR10.
2. Abrade bondline with a smooth abrasive pad or wetted TEROSON ET Cleaning sponge.
3. Wipe off again surface with a lint free cloth and TEROSON VR 10.
Storage:
Frost sensitive: no Recommended storage temperature : 5 to 25 °C Shelf life : 12 months foil pack 18 months aluminium cartridge
Parameters:
Colour: black Odour: weak Consistency: smooth, sag-resistiant, pasty Density g/cm³: approx. 1.25 Solids: 100 % Curing mechanism: humidity curing Cure rate: (DIN 50014; 23°C, 50% rh) : approx. 3 to 4 mm / 24 h Shore-A-hardness: (DIN 53505): approx. 70 Tensile strength: (DIN 53504) approx. 9.5 MPa Stress: (DIN 53504) approx. 4 MPa at 100 % elongation Shear modulus: (according to DIN 54451) approx. 2.9 MPa Elongation at break: (DIN 53504) approx. 350 %
Full technical information can be found in the technical data sheet.
The direct glazing adhesive is outstanding for the following properties:
- Very good sag resistance
- High cure rate
- High elastic and shear strength, even after aging
- Very low conductivity
- Good adhesion to the remaining material
- High shear modulus
- High UV resistance in connection with primer/activator
- Excellent adhesion to glass, glass with the ceramic coating, encapsulation and to painted surfaces, in connection withprimer/activator
Further information about the product: biuro@woronko-kleje.pl
Application Areas:
TEROSON PU 8597 HMLC is used for the bonding of front, rear and side screens to the body of motor-, utility-, special- and rail vehicles.
Directions for use:
Surface Preparation:
The substrates to be bonded must be dry and free from oil, dust, grease and other contaminations. Check new glass if it is correct and free of any damage. To obtain an optimal adhesion on the new screen we recommend 2 different surface preparation methods (solvent based, TEROSON VR 10 or waterborne, TEROSON VR 100):
1. Wipe off surface with a lint free cloth and TEROSON VR10.
2. Abrade bondline with a smooth abrasive pad or wetted TEROSON ET Cleaning sponge.
3. Wipe off again surface with a lint free cloth and TEROSON VR 10.
Storage:
Parameters:
Full technical information can be found in the technical data sheet.