LOCTITE FREKOTE C-200 - 5L (środek antyadhezyjny do form)
Nr
IDH.377284
Cena
518,14 PLN netto
Product description:
LOCTITE® FREKOTE® C-200 is a unique water based release agent designed to provide multiple release with no contaminating transfer. This product can be applied to molds at temperatures between 60°C to 205°C. LOCTITE® FREKOTE® C-200 chemically bonds to the mold surface to form a thin, chemically resistant coating. It releases thermoset composites as well as thermoplastics in roto molding processes. LOCTITE ® FREKOTE® C-200 contains no CFC's and no chlorinated, aromatic or petroleum based solvents which provides a very low VOC content and non-flammability. When used according to directions, LOCTITE FREKOTE® C-200™ gives no mold build up and exhibits high thermal stability for all molding processes. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Apply LOCTITE® FREKOTE® C-200™ to molds pre-heated to a minimum of 60°C. LOCTITE® FREKOTE ® C-200™ is suitable for mold temperatures up to 205°C.
2. Apply LOCTITE® FREKOTE® C-200™ using a finely atomized fan pattern. Regulate the gun output to 60 - 90 ml/minute for molds heated from 60°C - 150°C. Molds above 150°C regulate gun output to 120 - 150 ml/minute.
3. At 60°C, LOCTITE® FREKOTE® C-200™ will dry in a few seconds and be fully cured after 40 minutes. At 100°C, cure time is reduced to 20 minutes, and at 120 °C LOCTITE® FREKOTE® C-200™ cures in 15 minutes.
4. For hot 120°C - 205°C molds, or porous molds, apply a minimum of 6 coats. For temperatures ranging from 60°C - 120°C, a minimum of four coats should be applied with care taken to avoid emulsion accumulation and run marks due to over application. Allow time for the release agent to cure prior to production.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
Technology: Mold Release Appearance: White emulsionLMS Chemical Type: Water based emulsion Odor: Slight mild Cure: Heat cure Cured: Thermal Stability ≤315 °C Application: Release Coatings Application Temperature 60 to 205°C Specific Benefit:
- No contaminating transfer
- Reduces rejection rates
- Low VOC
- No measuring or mixing
- Multiple releases
- No mold build-up
Full technical information can be found in the technical data sheet
LOCTITE® FREKOTE® C-200 is a unique water based release agent designed to provide multiple release with no contaminating transfer. This product can be applied to molds at temperatures between 60°C to 205°C. LOCTITE® FREKOTE® C-200 chemically bonds to the mold surface to form a thin, chemically resistant coating. It releases thermoset composites as well as thermoplastics in roto molding processes. LOCTITE ® FREKOTE® C-200 contains no CFC's and no chlorinated, aromatic or petroleum based solvents which provides a very low VOC content and non-flammability. When used according to directions, LOCTITE FREKOTE® C-200™ gives no mold build up and exhibits high thermal stability for all molding processes. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
1. Apply LOCTITE® FREKOTE® C-200™ to molds pre-heated to a minimum of 60°C. LOCTITE® FREKOTE ® C-200™ is suitable for mold temperatures up to 205°C.
2. Apply LOCTITE® FREKOTE® C-200™ using a finely atomized fan pattern. Regulate the gun output to 60 - 90 ml/minute for molds heated from 60°C - 150°C. Molds above 150°C regulate gun output to 120 - 150 ml/minute.
3. At 60°C, LOCTITE® FREKOTE® C-200™ will dry in a few seconds and be fully cured after 40 minutes. At 100°C, cure time is reduced to 20 minutes, and at 120 °C LOCTITE® FREKOTE® C-200™ cures in 15 minutes.
4. For hot 120°C - 205°C molds, or porous molds, apply a minimum of 6 coats. For temperatures ranging from 60°C - 120°C, a minimum of four coats should be applied with care taken to avoid emulsion accumulation and run marks due to over application. Allow time for the release agent to cure prior to production.
Storage:
Store product in the unopened container in a dry location. Storage information may be indicated on the product container labeling. Optimal Storage: 8 °C to 21 °C. Storage below 8 °C or greater than 28 °C can adversely affect product properties. Material removed from containers may be contaminated during use. Do not return product to the original container. Henkel Corporation cannot assume responsibility for product which has been contaminated or stored under conditions other than those previously indicated.
Parameters:
- No contaminating transfer
- Reduces rejection rates
- Low VOC
- No measuring or mixing
- Multiple releases
- No mold build-up
Full technical information can be found in the technical data sheet