TEROSON SB S3000 BK - 1l (ochrona przed uderzeniami kamieni, czarny)
Nr
IDH.2671621
Cena
111,85 PLN netto
Skojarzone produkty:
TEROSON SB S3000 BK - 1l (ochrona przed uderzeniami kamieni, czarny)
Skojarzone produkty:
Product description:
TEROSON SB S3000 is a solvent containing, high viscosity, sprayable coating material based on artificial resin.The material demonstrates particularly fast drying characteristics and can be over painted quickly. After complete drying, the coating exhibits an abrasionresistant corrosion protection with good stone chip protection properties and good ageing characteristics. The dry film provides excellent adhesion to bare, primed and painted sheet metal and to plastics coatedwith primer or filler. TEROSON SB S3000 can be painted with standard vehicle paint systems (conventional and water based).Oven drying of painted as well as unpainted parts is possible without problems. After complete drying the coating can be sanded. TEROSON SB S3000 has a high sag resistance together with excellent spraying properties. This allows creating nearly every desired surface texture. TEROSON SB S3000 is temporarily resistant against gasoline and cold cleaners.
Application Areas:
TEROSON SB S3000 is used to protect visible vehicle parts against corrosion due to stone chip damage, salt and humidity and allows to recreate the original surface of the stone chip protection coating, once painted. TEROSON SB S3000 is not suitable for coating elastic materials. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pre-Treatment:
Surfaces to be coated with TEROSON SB S3000 have to be clean, dry and free of rust, grease, dust and other contamination. Areas not be coated should be properly covered. Adhesion of TEROSON SB S3000 can be improved by roughening the surfaces to be coated with abrasive paper/pad.
Application:
TEROSON SB S3000 is applied with the Teroson UBC-Gun from 1-I-cans. Recommended application pressure 4 to 5 bar.Shake can well before use. After product application, close container tightly to avoid skin formation inside the container.Fine surface structures can be obtained with a standard filler gun available in every paint shop. The layer thickness ofTEROSON SB S3000 should not exceed 1 mm. This maximum layer thickness should be preferably applied in more than one spray cycle.
Storage:Frost sensitive : No Recommended storage temperature, °C: : 10 to 25
Parameters: Colour : black Odour : scent of aromatics Consistency : viscous, liquid Density : ~1.22 g/cm³ Solids : ~59 % Sag resistance : good Layer thickness wet : up to 1 mm Diluent / Pretreatment : TEROSON VR 40 Surface drying : 2 to 3 hrs. Completely dry : over night Application temperature : 10 to 25 °C In service temperature range : -25 to 80 °C Short exposure (up to 1 h) : 100 °C
Full technical information can be found in technical data sheet
TEROSON SB S3000 is a solvent containing, high viscosity, sprayable coating material based on artificial resin.The material demonstrates particularly fast drying characteristics and can be over painted quickly. After complete drying, the coating exhibits an abrasionresistant corrosion protection with good stone chip protection properties and good ageing characteristics. The dry film provides excellent adhesion to bare, primed and painted sheet metal and to plastics coatedwith primer or filler. TEROSON SB S3000 can be painted with standard vehicle paint systems (conventional and water based).Oven drying of painted as well as unpainted parts is possible without problems. After complete drying the coating can be sanded. TEROSON SB S3000 has a high sag resistance together with excellent spraying properties. This allows creating nearly every desired surface texture. TEROSON SB S3000 is temporarily resistant against gasoline and cold cleaners.
Application Areas:
TEROSON SB S3000 is used to protect visible vehicle parts against corrosion due to stone chip damage, salt and humidity and allows to recreate the original surface of the stone chip protection coating, once painted. TEROSON SB S3000 is not suitable for coating elastic materials. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Pre-Treatment:
Surfaces to be coated with TEROSON SB S3000 have to be clean, dry and free of rust, grease, dust and other contamination. Areas not be coated should be properly covered. Adhesion of TEROSON SB S3000 can be improved by roughening the surfaces to be coated with abrasive paper/pad.
Application:
TEROSON SB S3000 is applied with the Teroson UBC-Gun from 1-I-cans. Recommended application pressure 4 to 5 bar.Shake can well before use. After product application, close container tightly to avoid skin formation inside the container.Fine surface structures can be obtained with a standard filler gun available in every paint shop. The layer thickness ofTEROSON SB S3000 should not exceed 1 mm. This maximum layer thickness should be preferably applied in more than one spray cycle.
Storage:
Parameters:
Full technical information can be found in technical data sheet
