TEROSON PU 8599 HMLC - 310ml (jednoskładnikowy klej poliuretanowy do szyb, super szybki 15 min, dawny Terostat 8599 HMLC
Nr
IDH.450441
TEROSON PU 8599 HMLC - 310ml (jednoskładnikowy klej poliuretanowy do szyb, super szybki 15 min, dawny Terostat 8599 HMLC
Product description:
Application Areas:
TEROSON PU 8599 HMLC is used for the bonding of front, rear and side screens to the body of motor-, utility-, specialand rail vehicles. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Preliminary Statement:
Prior to use it is necessary to read the Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed.
Priming:
With the use of an applicator apply a thin layer of All-in-one primer TEROSON PU 8519P to the cleaned substrate surface. Ensure the wet film should be 0.025 mm. Let the primed surface evaporate for approx. 2 minutes before the direct glazing sealant is applied. If a fresh bonding is made directly on the remaining material layer (left in the window cut–out of the body), this layer should not be primed within the first 2 hours after cutting back. But if the remaining layer is not used within the first 2 hours, it has to be activated with TEROSON PU 8519P. Provided that it is not contaminated with dust or grease, the remaining layer is the best adhesive surface, if TEROSON PU 8599 HMLC is used for the new bond. If windows are bonded which have been pre-coated with a primer or PUR–based adhesive/sealant by the glass supplier, the primer TEROSON PU 8519P is also suitable to ensure the correct adherence of TEROSON PU 8599 HMLC to the pre-coating. By means of an applicator, a thin layer of TEROSON PU 8519P is applied to the pre-coating. Following this, an evaporation time of approx. 2 minutes has to be observed. Subsequently, TEROSON PU 8599 HMLC is applied as usual, but taking into consideration the layer thickness of the pre-coating.
Processing:
Prior to its use, the cartridge or foil pack of TEROSON PU 8599 HMLC must be warmed in the cartridge warming box for at least 15 minutes, resp. 30 minutes in the pre-heating box for cartridges and foil packs. The direct glazing sealant TEROSON PU 8599 HMLC is processed from the cartridge or foil pack using commercial equipment such as hand, battery driven or air-pressure guns with a piston rod.
Storage:
Frost sensitive : no Recommended storage temperature : 5 to 25 °C Shelf life : 12 months foil pack 18 months aluminium cartridge
Parameters:
Colour: black Odour: weak Consistency: smooth, pasty, sagresistant Density g/cm³: approx. 1.25 Solids: 100 % Curing mechanism: humidity curing Cure rate: (DIN 50014; 23°C, 50% rh) : approx. 3 to 4 mm / 24 h Shore-A-hardness (DIN 53505) : approx. 75 Tensile strength (DIN 53504) : approx. 10.5 MPa Stress (DIN 53504) : approx. 6 MPa at 100 % elongation Shear modulus (according to DIN 54451) : approx. 3.2 MPa Elongation at break (DIN 53504) : approx. 350 %
Full technical information can be found in the technical data sheet
Application Areas:
TEROSON PU 8599 HMLC is used for the bonding of front, rear and side screens to the body of motor-, utility-, specialand rail vehicles. Further information about the product: biuro@woronko-kleje.pl
Directions for use:
Preliminary Statement:
Prior to use it is necessary to read the Safety Data Sheet for information about precautionary measures and safety recommendations. Also, for chemical products exempt from compulsory labeling, the relevant precautions should always be observed.
Priming:
With the use of an applicator apply a thin layer of All-in-one primer TEROSON PU 8519P to the cleaned substrate surface. Ensure the wet film should be 0.025 mm. Let the primed surface evaporate for approx. 2 minutes before the direct glazing sealant is applied. If a fresh bonding is made directly on the remaining material layer (left in the window cut–out of the body), this layer should not be primed within the first 2 hours after cutting back. But if the remaining layer is not used within the first 2 hours, it has to be activated with TEROSON PU 8519P. Provided that it is not contaminated with dust or grease, the remaining layer is the best adhesive surface, if TEROSON PU 8599 HMLC is used for the new bond. If windows are bonded which have been pre-coated with a primer or PUR–based adhesive/sealant by the glass supplier, the primer TEROSON PU 8519P is also suitable to ensure the correct adherence of TEROSON PU 8599 HMLC to the pre-coating. By means of an applicator, a thin layer of TEROSON PU 8519P is applied to the pre-coating. Following this, an evaporation time of approx. 2 minutes has to be observed. Subsequently, TEROSON PU 8599 HMLC is applied as usual, but taking into consideration the layer thickness of the pre-coating.
Processing:
Prior to its use, the cartridge or foil pack of TEROSON PU 8599 HMLC must be warmed in the cartridge warming box for at least 15 minutes, resp. 30 minutes in the pre-heating box for cartridges and foil packs. The direct glazing sealant TEROSON PU 8599 HMLC is processed from the cartridge or foil pack using commercial equipment such as hand, battery driven or air-pressure guns with a piston rod.
Storage:
Parameters:
Full technical information can be found in the technical data sheet
