Serwis korzysta z plików cookies w celu świadczenia spersonalizowanych usług na najwyższym poziomie, w tym usług statystycznych oraz w celu dostosowania zawartości do indywidualnych preferencji użytkowników. Zapisywanie plików cookies można wyłączyć w ustawieniach przeglądarki. Więcej informacji
OK
Utwórz konto
[zamknij]     

TEROSON WX 210 - 500ml spray (zabezpieczenie antykorozyjne, wosk)

TEROSON WX 210 - 500ml spray (zabezpieczenie antykorozyjne, wosk) (IDH.795890)

Product description:
TEROSON WX 210 is an anti-corrosion agent for area coating and for the protection of cavities, containing mild smelling solvents. It is a thin, slightly thixotropic spray which atomizes easily. The anticorrosion agent is bitumen free and has a strong neutralisation power and thus good acid binding capacity. The product contains a high proportion of rust inhibitors. The polymer portion leads to high toughness and relative high abrasion resistance compared to other wax products. TEROSON WX 210 is very finely atomized on spraying, has outstanding creep qualities, penetrates well into the spaces to be protected (e.g. welds) and yet does not run excessively from the bottom of such joints. Creep qualities are optimal if the product and the bodywork are at room temperature.When fully dry, the anti-corrosion agent forms a tough, plastic, water-repellent film of translucent thin layers. The aerosol can is equipped with two spray heads: one spray head with a tube, one spray head with a slit nozzle for area coating. Further information about the product: biuro@woronko-kleje.pl

Applications area:
TEROSON WX 210 is used in workshops primarily as conservation wax for preventive protection and for care and repair. With the new type of fan jet spraying head underbodies of cars can be evenly coated with a widespread jet. The attached round jet spraying head with tube allows spraying in cavities on cars, e.g. doors, motor hoods, trunk lids and areas difficult to reach. TEROSON WX 210 is suitable for spraying the interior of open cavities, in addition to existing cavity conservation of new vehicles and follow-up treatment after accident repairs. The product is ideal for corrosion protection on sheet metal and steel parts, e.g. fuel tanks, brake tubes or tubes of the power assisted steering. Screw connections at gearbox crossrails and engine suspensions can also be coated with this translucent protection film. The thread is thus protected and will enable secure screwing. On modern cars TEROSON WX 210 completes the factory coating on transitions, under plastic hoods, in the weal houses and under the fenders. The splash water resistant film permanently protects concealed body areas. Body seams under bumpers which are no longer caulked in the factory can be securely sealed. TEROSON WX 210 is particularly suitable for long term protection of immobilized vehicles. The product is also used for the conservation of seams, areas and cavities on vehicles and rust endangered spots in the engine compartment. Slightly sprayed rubber parts will show a dull gloss and a fresh appearance. Building machinery, agricultural equipment and gardening implements, e.g. the underbody of lawn mowers, hoes and spades can also be excellently maintained and protected.

Directions for use:
Preparation:
Any items of trim and covers should be removed. Any rust should be removed as far as possible. To spray awkward areas (e.g. semi-hollow zones such as doors etc.), the special spray head with the tube is used. The material should be at room temperature when used. If stored for long periods and if the material is at a temperature below 15°C, the material becomes more thixotropic. Therefore the can should be shaken vigorously before use until the ball-bearing becomes audible.

Spraying:
The body parts (which should be free from dust and grease) should be sprayed evenly, with the can held upright during spraying. When using the spray tube, this can be moved slowly in circles whilst spraying so that all directions are covered. After use the can should be held with the valve down and the spray should be activated until the jet is cleared and only propellent is emitted.

Storage:
  • Frost sensitive : no
  • Recommended storage temperature :15 to 25 °C; (never heat above 50 °C!)
  • Shelf life : 18 months

    Parameters:
  • Colour : beige-translucent
  • Odour : mild odour
  • Density : approx. 0.85 g/cm³
  • Solid : approx. 40 %
  • Consistency : thin liquid. slightly thixotropic
  • Drop point of solid (DIN 51801) : >100 °C
  • Sag resistance : min. 100 µm
  • Penetration : >13 mm
  • Behaviour in the repair paint oven (1.5 hrs at 90°C) no running off
  • Dry film thickness : 50 µm
  • Application temperature : 15 to 25 °C
  • In service temperature : -40 to 100 °C
  • Short exposure (up to 1 h) : 130 °C

    Full technical information can be found in the technical data sheet
  • Asortyment